by You load up your Bosch dishwasher, press start, and notice the red InfoLight on the floor start blinking. What gives?
This handy light is supposed to let you know when your dishwasher is running, not blink at you like a frustrated stop light. But don’t worry, there are a few common issues that cause this blinking, and most are easy to fix.
Bosch Dishwasher Blinking Red Light
In this guide, we’ll explore the most likely reasons your Bosch dishwasher’s InfoLight is blinking red when you try to run it, along with the best way to get your machine washing dishes again.
What is the InfoLight on a Bosch Dishwasher?
The InfoLight is a small red light found on many Bosch dishwasher models. It shines on the floor to let you know when the dishwasher is running.
When operating normally, the InfoLight will stay solid red throughout the wash cycle. Once the cycle finishes, it turns off.
The InfoLight provides a convenient way to know if your dishwasher is running, especially for Bosch models that have hidden controls and are extra quiet.
Why Does My Bosch Dishwasher Blinking Red Light?
When the InfoLight blinks red instead of staying solid, it’s typically signaling one of the following issues:
- Low rinse aid
- Problem with the door
- Didn’t start cycle properly
- Dishwasher is stuck
- Dirty or damaged door seal
- Delay start or paused cycle
- Error code
We’ll cover each of these common causes in more detail next.
Top Reasons Your Bosch Dishwasher’s InfoLight Blinks in Red Color:
Here are the most likely reasons your Bosch dishwasher’s InfoLight is blinking red when you try to run it, and how to fix the issues:
-
1. Low Rinse Aid
If you’re using a wash setting that requires a rinse aid, like PureDry or CrystalDry, a low rinse aid level can cause the InfoLight to blink.
To check: Open the rinse aid compartment next to the detergent cup and see if the level is low.
To fix: Add more rinse aid until it reaches the max fill line. Make sure you’re using a rinse aid compatible with your Bosch model.
-
2. Problem with the Door
Issues with the door latching and sealing properly are another common reason for a blinking InfoLight.
To check:
- Inspect for obstructions around the door seal.
- Ensure racks are pushed in fully.
- Test closing the door to feel for resistance.
- Inspect the door seal for damage.
- Check the door latch operation.
To fix: Remove any obstructions, realign/replace seals, or replace faulty door latches as needed.
-
3. Didn’t Start Cycle Properly
If you don’t press start and close the door quickly enough, it can cause a blinking light.
To fix: Press start, then immediately close the dishwasher door. This aligns the timing so the dishwasher recognizes the door is latched before starting the cycle.
-
4. Dishwasher is Stuck
Control board errors can also lead to a stuck dishwasher and blinking InfoLight.
To check: Do a power reset or control panel reset. This clears any minor glitches.
To fix: If resets don’t work, you may need a technician to diagnose and replace the control board.
-
5. Dirty or Damaged Door Seal
A dirty or damaged door seal prevents a proper watertight seal when closed.
To check: Inspect the door seal for debris buildup, tears, and proper alignment.
To fix: Clean the seal thoroughly and realign or replace it if damaged.
-
6. Delay Start or Paused Cycle
If you have Delay Start activated or pause a cycle mid-wash, the InfoLight will blink as a reminder.
To fix: For Delay Start, cancel the setting to start the wash immediately. For a paused cycle, press On/Off to resume.
-
7. Error Code
The InfoLight blinking may be accompanied by an error code on the display, signaling a detected fault.
To check: Open the door to check for an error code on the display panel.
| Error Code | Meaning |
|---|---|
| E01 | Water supply error |
| E02 | Heating element error |
| E03 | Not filling with water |
| E04 | Water not draining |
| E05 | The door not closing properly |
| E06 | Water sensor error |
| E07 | The intake opening is covered |
| E08 | Low water level |
| E09 | Water intake fault |
| E12 | Limescale build-up |
| E14 | Flow sensor error |
| E15 | Water in the base pan |
| E16, E17, E18 | Water flow problem |
| E24 | Drain pump error |
| E22 | Filter is blocked |
| E25 | The drain pump is blocked, the Filter is clogged Pump impeller is jammed |
| E27 | The voltage is too low |
To fix: Consult your owner’s manual for that code and recommend actions to clear it. This often involves repairs.
-
8. Child Lock is On
The InfoLight can also blink when the child lock is enabled, preventing the dishwasher from starting.
To fix: Disable the child lock feature. On most models, press and hold the Child Lock button for a few seconds.
What Bosch Dishwasher Models Have an InfoLight?
The InfoLight feature is found on most Bosch 300, 500, and 800 series dishwashers with hidden controls.
Some popular Bosch dishwasher models with an InfoLight include:
- SHXM63WS5N
- SHSM63W55N
- SHVM63W53N
- SHPM65W55N
- SHXM65W55N
- SHPM78W55N
- SHXM78W55N
- SHVM78W53N
- SHPM98W75N
- SHXM98W75N
- SHVM98W73N
And many more! Check your model number if you’re unsure.
Which are the Most Affected Models Getting InfoLight Issues:
| Name | Model Number |
|---|---|
| Bosch – 300 Series 24″ Bar Handle Dishwasher with Stainless Steel Tub | SHXM63WS5N |
| Bosch – 300 Series 24″ Scoop Handle Dishwasher with Stainless Steel Tub | SHSM63W55N |
| Bosch 300 Series 24″ Custom Panel Dishwasher with 16 Place Setting Capacity | SHVM63W53N |
| Bosch SHPM65W55N 24″ 500 Series Built In Fully Integrated Dishwasher | SHPM65W55N |
| Bosch 500 Series 24 In. Built In Fully Integrated Dishwasher | SHXM65W55N |
| Bosch 24″ 800 Series Built In Fully Integrated Dishwasher | SHPM78W55N |
| Bosch 800 24″ Dishwasher, 42 dB, 6/5 cycles – Flex 3rd Rack, InfoLight | SHXM78W55N |
| Bosch 800 Series Dishwasher with 3rd Rack, InfoLight®, and AquaStop® | SHVM78W53N |
| Bosch 800 Series 24 Inch Built In Fully Integrated Dishwasher | SHPM98W75N |
| Bosch 800 24″ Dishwasher, 39 dB, 6/6 cycles – MyWay 3rd Rack, InfoLight | SHXM98W75N |
| Bosch 800 Series Dishwasher with MyWay™ 3rd Rack, RackMatic®, AquaStop | SHVM98W73N |
| Bosch Series 4 Fully Retractable Dishwasher 60cm | SMV4EDX17E |
| Bosch 24″ 500 Series Pocket Handle Dishwasher with 16 Place Settings | SHPM65Z55N |
| Bosch 24″ 800 Series Fully Integrated Pocket Handle Dishwasher with Flexible 3rd Rack, InfoLight and CrystalDry | SHPM78Z55N |
| Bosch – 800 Series 24″ Top Control Built-In Dishwasher with CrystalDry, 42 dBa | SHXM78Z55N |
| Bosch 800 Series 24 Inch Fully Integrated Panel Ready Dishwasher with Touch Control Technology | SHVM78Z53N |
| 24″ Bosch 800 Series Top Control Built-In Dishwasher with Stainless Steel Tub | SHVM78Z53N |
| 24″ Bosch Benchmark Fully Integrated Smart Dishwasher | SHV88PZ63N |
| Bosch 500 Series 24 Inch Built In Bar Handle Dishwasher with 5 Wash Cycles | SHXM65Z55N |
| Bosch Dishwasher 24” Stainless steel | SHX65T5XUC |
| Bosch 300 Series SHS63VL2UC Fully Integrated Dishwasher | SHS63VL2UC |
| BOSCH Fully Integrated Dishwasher – 13 Place Setting – InfoLight – D Energy | SMV2HAX02G |
Most Common Questions about Bosch Dishwasher InfoLight Issues
Here are answers to some frequently asked questions about dealing with a blinking InfoLight on your Bosch dishwasher:
- Q: Why does my InfoLight come on but the dishwasher won’t start?
A: This usually indicates a problem with the door latch or seal. Check for obstructions and test closing the door.
- Q: My InfoLight blinked and now the dishwasher is completely dead. What’s wrong?
A: It could be a control board failure after an error code/fault. Try rebooting the dishwasher and check for control panel lights/response.
- Q: The dishwasher was working fine then the InfoLight started blinking mid-cycle. Why?
A: Your dishwasher is likely stuck due to a software error. Try resetting the control panel to clear any glitches.
- Q: I tried all the InfoLight troubleshooting tips but nothing works. Now what?
A: At this point, it’s best to call in a technician who can diagnose the issue and identify any necessary repairs or part replacements required.
- Q: Does the InfoLight ever blink when the dishwasher is working okay?
A: It shouldn’t. The InfoLight should stay solid red when operating normally and turn off when the cycle finishes.
- Q: The InfoLight blinks when I first turn on my dishwasher then stays solid. Is this normal?
A: Yes, it’s normal to briefly blink when first powering on before remaining solid during the cycle.
- Q: How can I stop my dishwasher’s InfoLight from blinking at night?
A: Unfortunately there is no way to disable the InfoLight. You’ll need to repair the underlying issue causing the blinking.
- Q: I have no InfoLight at all. Could a faulty LED bulb cause blinking?
A: It’s unlikely. More probable causes are control board errors, door latch problems, or a bad door switch.
- Q: Will running empty cycles help reset or fix my dishwasher’s blinking InfoLight?
A: Empty test cycles alone likely won’t fix it. You need to diagnose the specific issue first, then take appropriate repair steps.
- Q: How do I reset my Bosch dishwasher control panel?
A: Press and hold the Start/Reset button for 5+ seconds until the lights shut off. This resets the controls and can clear some errors.
How to Fix When Your Bosch Dishwasher InfoLight Blinks?
If your Bosch dishwasher’s InfoLight is suddenly blinking red instead of staying solid, use this troubleshooting guide:
- Check rinse aid level and refill if low.
- Inspect for door obstructions and seals. Test door latching.
- Ensure the dishwasher starts properly by pressing start and then immediately closing the door.
- Do a reset on the control panel and power reboot.
- Clean and realign the door seal if dirty or damaged.
- Cancel Delay Start or resume the paused cycle.
- Check for error codes on the display and look up steps to clear it.
- Call for service if you’ve tried all troubleshooting without success.
You can often identify the cause and take steps to get your InfoLight back to normal operation. But for any complex repairs, rely on the experts.
Bosch Customer Support
- Reach out to Bosch Customer Support at 1-800-944-2904 or text “SUPPPORT” to 21432 for Quick Support. Know More.
More Dishwasher Blinking Guides:
Conclusion:
That wraps up our guide on deciphering the Bosch Dishwasher Blinking Red Light! Hopefully, this breakdown of common causes and fixes helps you resolve the issue when that annoying light pops up.
Don’t stress – with some basic troubleshooting, you’ll likely have the appliance back in working order. If it persists, call in reinforcements from the Bosch experts.
And please share this guide with friends and family who have Bosch dishwashers! I’d love to hear if the information helped you or if I missed any other blinking light scenarios.
Leave a comment below with your experiences and advice!
